Description
PRODUCT PROFILE
FLOORCOAT is a high grade, 100% solids, polyamide epoxy with non-yellowing, UV protection. FLOORCOAT is designed as a clear high-strength, performance enhanced adhesive and preservation sealant for flooring applications. FLOORCOAT is widely used in residential and commercial applications. Dyes, silicas, sands and other materials can be added within the product for desired results. FLOORCOAT is a 2 part, 2 to 1 ratio, professional grade system that enhances and preserves new projects and replaces existing surfaces with a permanent, scratch resistant gloss finish. FLOORCOAT will provide projects with beautifully clear results while being safe to apply, with very minimal odor and NO VOCs. A slip resistant topcoat can be obtained within the product for optimum safety if required.
PRODUCT FEATURES & BENIFITS
- Ideal for professional flooring projects.
- Museum grade, ultra clear top-coat with UV protection.
- Permanently enhances surfaces with wear resistant, chemical resistant and water proof properties.
- Quick and easy – can be applied by brush, roller or sprayer (45:1 airless or higher).
- Easy 2 to 1 mix ratio.
- Ideal for all flooring surfaces.
- 100% solids, free of volatile compounds, fumes and odor.
PRODUCT PROFILE
FLOORCOAT is a high grade, 100% solids, polyamide epoxy with non-yellowing, UV protection. FLOORCOAT is designed as a clear high-strength, performance enhanced adhesive and preservation sealant for flooring applications. FLOORCOAT is widely used in residential and commercial applications. Dyes, silicas, sands and other materials can be added within the product for desired results. FLOORCOAT is a 2 part, 2 to 1 ratio, professional grade system that enhances and preserves new projects and replaces existing surfaces with a permanent, scratch resistant gloss finish. FLOORCOAT will provide projects with beautifully clear results while being safe to apply, with very minimal odor and NO VOCs. A slip resistant topcoat can be obtained within the product for optimum safety if required.
General Surfaces must be clean and dry. Remove all dirt, dust, oil and all other contaminants.
Primer Self priming on most surfaces, but apply Dynesic’s DX-1100 Primer prior to FLOORCOAT on concrete surfaces.
- Metal, Galvanized – Many applications can be pressure washed or even scrubbed using a degreaser such as Dynesic’s DX-ETCH or with water (if there is no chance of oils or greases remaining on the surface). In more extreme conditions, or depending on surface type, obtaining an etched surface is recommended.
- Stainless Steel Topcoat products have a difficult time adhering to slick surfaces, however, FLOORCOAT’s 2750 psi adhesion strength allows it to fully adhere to stainless steel. We recommend an etched profile that can be achieved by sand blasting or grinding. Keep in mind t that an etched, rather than a polished profile is the goal.
- Concrete/CMU Concrete must be cured 28 days at 75°F (24°C) and 50% relative humidity or equivalent. Prepare surfaces in accordance with ASTM D4258 Surface Cleaning of Concrete and ASTM D4259 Abrading Concrete. Voids in concrete may require surfacing with PANSEAL Paste Grade (2500PG) to fill and strengthen the substrate. Prime concrete surfaces first with Dynesic DX-1100 Concrete Primer.
- Fiberglass, Wood Clean and apply.
* To coat over previously painted surfaces contact Dynesic’s Technical Service Department.
MIXING & THINNING
Mixing: Power mix part A resin separately, then add part B hardener and power mix. If using a thinner or additive, add and mix to part A prior to adding the hardener (Part B).
Thinning: For Brush: Up to 16 oz/gal (12%) w/ Acetone or Xylene
For Roller: Up to 16 oz/gal (12%) w/ Acetone or Xylene
* Use of thinners other than those supplied or recommended by Dynesic may adversely affect product performance and void product warranty, whether expressed or implied.
Ratio 2:1 ratio (A to B) by volume
Pot Life 8 hours 20 minutes at 5°C (41°F)
2 hours at 25°C (77°F), 50 minutes at 33°C (92°F)
* Do not keep the blended coating in the original container unless immediate use is planned. Otherwise, exothermic heat created during the curing process will considerably shorten the pot life. Pour the coating into a rolling tray or pour directly onto the surface. Try to keep the depth of the coating in the tray below 3/8”.
APPLICATION GUIDELINES
Listed below are general equipment guidelines for the application of this product. Job site conditions may require modifications to these guidelines to achieve the desired results.
CLEANUP & SAFETY
Cleanup Use MEK or Acetone. In case of spillage, absorb and dispose of in accordance with local, applicable regulations.
Safety Read and follow all caution statements on this product data sheet and on the MSDS for this product. Wear protective clothing, gloves.
